Bing Pig restoration

Here is the restoration process of Bing #70. Done by our very own Bing historian Tom Moss!

Not quite Mena Suvari in a bed of roses... but it's a beauty, again!

Finished board. Still a classic "pig".

The glass was specially treated on the fin to show the weave, giving it that early 60s look, and to help hide some of the repaired damage underneath.

Original condition, with a dark suntan, lots of fiberglass delamination and nose and tail dings.

After stripping the glass off, the surface of the foam was very brown, exfoliating (peeling) and bubbled. The blank was sanded down to good foam and all the bubbles cleaned out.

The stringer had separated from the foam and was broken in five places and punky (rotten) in the nose and tail.

Glued and taped (I used too much glue - I didn't realize it was going to expand).

What do you use to fill hundreds of craters in a surfboard blank? Remember it needs to be lightweight and sand as easily as the surrounding foam. I used lightweight spackle (several quarts!). Not recommended, but as long as the board stays out of the sun in the future, it should be ok... maybe.

The stringer has been reglued and the foam has been filled and reshaped. All the repairs have been color-matched and textured.

Ready to glass.

First layer of 10 ounce glass, trimmed and ready for resin.

One quart of laminating resin per layer of fiberglass.

The reproduced lam (with original number) is set in resin, before pulling second layer of fiberglass over the board.

Sanding the hot coat. The resin/fiberglass dust is really hell on my eyeball pterigiums, even with all the gear on. I bet Bing never had to sand a new board as much as I have sanded this one. At this rate, I'd be lucky to make one board a week working full-time at it.

I ran the tape out the length of the board and then dropped it down to pencil marks that I had made on the ends of the board, a half inch outside of the stringer. This is how I was told that the pros typically get a straight line along their panels. After taping off the stringer, I poured on my colored resin mix, spreading it evenly over the board. After the resin began to kick, I pulled the tape off, which revealed a big problem, as you can see in this picture - the clear space along both sides of the stringer was uneven… this was because the board’s stringer varies in width and is bowed, a lot (Thanks, Bing!).

– I decided that an unstraight line would not be as noticeable as the uneven space I presently had on the board. So, after sanding the color off, I measured and drew a line a half inch out from the stringer on both sides and then ran the tape along it. On the positive side, this mistake allowed me to have a second attempt at matching the color, which looked too red compared to the original carrot-juice color of the board.

– I added some more resin and mixed in various colors of pigment, finally getting the color to match the piece of colored fiberglass that I had kept from the original board. Blue pigment was the key to toning down the International Orange pigment. (For some reason, the camera does not pick up the orange hue very well.)

After pulling the tape, you can see that the space between the color and the stringer is very clean and even looking – can’t even tell that it is zig-zagging with the stringer.

Next lesson…With both sides color coated, it was time to lightly sand it, as preparation for the resin gloss coat. This is also the last chance to flatten out any remaining bumps and dips in the surface (the color coat is like an extra sanding coat, you know, at least that’s the way I was thinking). After sanding it pretty good, I noticed there was still one minor dip that bothered me, and I thought I’d hit it one more time. Woops! (not even close to what I said) – foam underneath suddenly became visible. Cringe. Of course, I didn’t have any colored resin mix left to try and patch it with. So, after thinking about it for a day, I started the entire process over – sand the color down on both sides of the board, remix resin and pigments, retape, clean off every speck of dust, pour and brush the color coat on, wait til its tacky, and pull the tape. One thing about surfboard repairs, you can always redo and correct, or hide, your mistakes, if you have enough patience or nothing better to do.

Filing the seam where the gloss coats on the deck and bottom overlap.

Wet sanding the gloss coat. Dr. Ding said that if I applied the gloss coat correctly, I might only need to hit it with the fine 400 and 600 grit paper... Yaeh right! I started with the much coarser 150 (because I had created more bumps and dips with the finishing resin) and then progressed to 220, then 320, 400 and finally 600.

Ready to be buffed. Tomorrow. I'm ready for a beer. in, http://www.classicbingsurfboards.com/

Surfing's mystic

Here are some shots of a few jim phillip's pigs.

undefined variables

more jim phillips

Puerto Rico 1968

Wayne Lynch 68 Puerto Rico

8'4'' PR / Putnam/ Hilburs

Always loved the way Wayne Lynch, Nat Young and Ted Spencer surfed in Evolution and the Hot Generation on these Mid length boards. Paul Gross really nailed an 8'4'' for me I still have , but after 17 years it's pretty beat. Hilburs and I made this a few years ago it's just tweeked on the rails, foil , and nose rocker. These really work in everything I surf, but I love this board in junk surf. It rolls on the rail like butter and cuts back so easy with that hip in the tail, fun stuff to look back, but improve (IMO) on old designs.

in, http://displacementia.blogspot.com/

Vans by Thalia Surf Shop Opening Night

60's Bing

Surfer ad April/May 1963

Mid 60's Bing Stock Models

Can you believe this is a stock model Bing! #7199 made in Feb. 67

in, http://www.classicbingsurfboards.com/

Siebert online shop

online shop: www.shop.siebertsurfboards.com

LAKE SURFERS ARE SO CORE...

Ryan Gerard is the owner and operator of Bing Surfboard's only Great Lakes dealer, Third Coast Surf Shop. Surfers have been sliding freshwater waves since the 1960s but with a recent growth in popularity, Ryan opened up shop in New Buffalo, MI in 2005 and has been leading the charge and spreading the stoke ever since. Above are a few pics of Ryan sliding his 9'4" NR Slim and one of him on a recent winters day (info from bingsurf.com).

in, www.bingsurf.com

Sam Cody

Meet the new BING airbrusher and pin line extraordinaire, Sam Cody. Sam recently joined the BING glassing team as an existing member of the Channin crew.

Sam’s not really “new” to BING at all because prior to going to work for Channin, Sam airbrushed BING Surfboards at the San Diego-based Gordon & Smith factory in the 1970′s.

in, http://www.bingsurf.com/

Bi/polar

this is a hull

this is a stubbie

this is fucking bi/polar sick

this is vouch

in, http://theblacksinglefincatastrophe.blogspot.com/

Michele Puliti....piggies DOUBLE TROUBLE!

Here some beauties based on classic Velzy template. 9.6 to 9.9 lenght piggies just came out from Ola Surfboards. The pig shapes are gettin more popular here in Italy thanks to mastercraftman Michele Puliti's hands and to SingleFin.it guys efforts to give more space to what the most call retro-surfing-culture but I call real-pleasure of surfing. Anyway, waiting for my brand new narrower nose "Mud Pig" designed along with Michele will be glassed, I wanna thank you for you blog. Pig, as once I read, is not RETRO but it's about the future!

from marco via: surfapig@live.com

in, http://surfapig.blogspot.com/

Al Knost

photo: jackb766, on Flickr

in, http://theohsea.blogspot.com/

Almond

Water photography provided by: Jimmy Pham

in, http://lifeisjustswell.blogspot.com/

Bing Team Rider Jesse Hinkle Elevates & Creates

El Segundo’s Jesse Hinkle may be Bing Surfboard’s youngest team rider (age 16), but he already knows how to express himself on the waves and in his art. Jesse adds his own personal touch to his new 9’5 Bing Elevator and elevates at the Noosa Festival of Surfing this past Spring.

in, http://www.bingsurf.com

Cy's Aquatic Almonds

There are only a handful of Cy's Aquatic Almonds in circulation so far, and somehow Patrick Derry owns two of them. Glad you found a longboard you can't live without. (times 2)

This is Cy #1 and Eco-Cy at the beach.

in, http://lifeisjustswell.blogspot.com/

Alex Knost - Profile

in, www.rebeltv.com